Stamina Products 55-1772 Manuel d'utilisateur

Model#: 55-1772STAMINA PRODUCTSMADE IN CHINAProduct May Vary SlightlyFrom Pictured.2008, 07Exercise can present a healthrisk. Consult a physicianbefo

ASSEMBLY INSTRUCTIONSRIGHTLEFT10ShaftLook down from the topLRSTEP 8: There is an "L" decal on the LEFT HANDLEBAR(8), and an "R" d

ASSEMBLY INSTRUCTIONS11STEP 11Refer to illustration A. Tie the STRAP to the plug end of the PULSE SENSOR WIRE(27). Pull the STRAPfrom the square hole

SET UP INSTRUCTIONS12Place the Magnetic 1772 Elliptical in the area where it will be used. It is recommended that the Magnetic1772 Elliptical be place

OPERATIONAL INSTRUCTIONS13LOAD ADJUSTMENTTo increase the load, turn the TENSION KNOB(25) clockwise.To decrease the load, turn the TENSION KNOB(25)coun

POWER OFF:Pedal movement or press any button.Automatic shut off after 4 minutes ofinactivity. Resets all values to zero.POWER ON:USING THE METERFUNCT

STORAGE151.2.3.4.To store the Magnetic 1772 Elliptical, simply keep it in a clean dry place.The minimum rest dimensions of the Magnetic 1772 Elliptica

16CONDITIONING GUIDELINESHow you begin your exercise program depends on your physical condition. If you have been inactive forseveral years or are sev

17WARM-UP and COOL-DOWNWarm-Up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warmup for two to five minu

PRODUCT PARTS DRAWING18FRONTBACKStrap

PARTS LIST19 1 Main Frame 1 2 Front Stabilizer 1 3 Rear Stabilizer 1 4 Left Pedal Arm 1 5 Right Pedal Arm 1 6 Upright 1 7 Stat

TABLE OF CONTENTSSafety Instructions 2Before You Begin 4Equipment Warning & Notice Labels 5Hardware Identification Chart 6Assembly Ins

PARTS LIST2049 Plastic Washer (M8 x ø18 x 2mm thick) 850 Round Plug (28.6mm) 451 Spacer 252 Large Washer (M16 x ø32 x 0.5mm thick) 353

21WARRANTYLIMITED WARRANTYMODEL 55-1772Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanshipunder n

22NOTES

IMPORTANT : Before filling out the form below make sure you have the right information.Refer to the parts list to make sure you're ordering the

3THANK YOU FOR PURCHASING THEMagnetic 1772 EllipticalTo help you get started, we have pre-assembled most of yourMagnetic 1772 Elliptical at the factor

BEFORE YOU BEGIN4THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY :Allen Wrench (6mm)Multi-opening WrenchRight HandlebarUprightMeterLower Pivoting ArmWar

5EQUIPMENT WARNING & NOTICE LABELSLabel is larger than actual sizeWARNING LABEL(91)W1This chart is provided to help identify the warning & not

Part No. and Description Qty65 Bolt, Button Head (M8 x 1.25 x 15mm) 966 Bolt, Button Head (M8 x 1.25 x 20mm) 272 Bolt, Hex Head (M6 x 1 x 35mm)

7STEP 1Attach the FRONT STABILIZER(2) to the MAIN FRAME(1) with CARRIAGE BOLTS(M8x1.25x75mm)(64), ARC WASHERS(M8)(87), LOCK WASHERS(M8)(89), and ACORN

ASSEMBLY INSTRUCTIONS8BracketCable EndSpring HookMetal FittingSTEP 3Refer to the inset drawing. Lay the UPRIGHT(6) on the floor close to the front of

ASSEMBLY INSTRUCTIONSPlace the front end of the RIGHT PEDAL ARM(5) on the ROLLER(58) of the FRONT STABILIZER(2).Connect the back end of the RIGHT PEDA